Updated November 2026
Stripping cloth diapers removes the residue that builds up from detergent, fabric softener, diaper cream and hard water, which can cause odors, repelling and leaks. A strip wash takes one extra cycle and restores the absorbency your diapers should have. Here is how to do it safely, and how to tell when your diapers need it.
How Do You Strip Cloth Diapers?
Stripping is a set of hot, detergent-free washes designed to lift buildup out of the fibers. Most families strip only when they notice a problem, not on a fixed schedule. Work through the steps below in order.
Shopping for one? See our guide: Cloth Diapers or Disposable (2026): Which Is Better for Your Baby?.
What You Need
- A washing machine with a hot water setting
- Plain, unscented laundry detergent or a dedicated diaper cleaner, measured as the manufacturer directs
- Your diapers and inserts, separated from any non-cloth items
- Clean towels for drying if you plan to air-dry afterward
Step 1: Check Your Diapers for Buildup
Before stripping, confirm the problem. Dampen a diaper and watch whether water beads on the surface or soaks in slowly. Beading water means the fibers are coated. Also check for a sour or ammonia smell when the diapers are warm or wet.
Step 2: Run a Hot Rinse Cycle
Start with a cold or warm rinse using no detergent. This clears loose waste and prepares the fabric. Skip this step only if the diapers are already fully clean.
Step 3: Run Hot Wash Cycles
Set the machine to the hottest water your diapers can tolerate. Check the care label on each product, since some synthetic fabrics and elastics have lower limits. Use a full hot wash with a normal amount of detergent, then run a second hot wash without any detergent. Repeat the detergent-free wash if the diapers still bead water.
Step 4: Dry and Test
Dry the diapers as you normally would, then repeat the water test. Absorbent fabric should soak up water within a few seconds. If it still beads, repeat the process. Most diapers respond after one or two strips.
Common Causes That Call for Stripping
Stripping fixes a specific set of problems. Knowing the cause helps you decide whether stripping will help or whether another fix is needed.
| Symptom | Likely Cause | Does Stripping Help? |
|---|---|---|
| Water beads on the surface | Detergent or conditioner buildup | Yes |
| Strong ammonia smell | Urine residue and mineral buildup | Yes |
| Leaks after a few uses | Reduced absorbency from coating | Often |
| Mold or mildew | Moisture left in the fabric | Clean first, then strip |
For more on preventing buildup in the first place, see How to Wash Cloth Diapers and How to Launder Cloth Diapers: A Step-by-Step Guide for Clean, Fresh Results.
Tips for Avoiding Future Buildup
- Use the amount of detergent the manufacturer specifies. Extra soap is the most common cause of residue.
- Skip fabric softener, which coats fibers and reduces absorbency.
- Use a rinse cycle that fully drains and refills the machine.
- Choose a detergent labeled safe for cloth diapers, and read the guidance in Choosing and Stripping Cloth Diaper Detergent.
- Strip only when needed, since frequent stripping can wear down elastics over time.
Common Mistakes to Avoid
- Stripping before confirming the problem, which wastes water and energy.
- Using bleach or harsh additives unless the product directions allow it.
- Running hot cycles on fabrics that the label says cannot take high heat.
- Drying diapers while they still have residue, which sets odors into the fibers.
Recommended Gear
- Plain, unscented laundry detergent makes stripping more effective because it avoids adding new residue. View on Amazon
- A dedicated cloth diaper cleaner is formulated to lift buildup without leaving behind a film. View on Amazon
FAQ
How often should I strip cloth diapers?
Strip only when you notice beading, odor or leaks, rather than on a set schedule. Most families need it every few months, though this varies with water hardness and detergent choice.
Can I strip cloth diapers with vinegar?
Some parents use vinegar, but manufacturers often advise against it because it can break down elastics and certain fabrics. Check your diaper brand’s guidance before using it. Consult the manufacturer or a professional if you are unsure.
Will stripping damage my diapers?
Stripping is generally safe when you follow the care label and avoid harsh chemicals. Repeated hot washing can wear elastics faster, so only strip as often as needed.
Conclusion
Stripping cloth diapers is a simple way to clear buildup and restore absorbency. Check for beading, run hot washes without extra detergent, and test again after drying. With good washing habits, you will need to strip far less often.

