Updated November 2026

Learning how to use inserts in cloth diapers takes a few minutes and makes a real difference in absorbency. You will learn how to place an insert in a cover, how to match the insert to your baby’s wetting pattern, and how to avoid the leaks that come from poor placement. Most of the work is in the setup, so once it’s right, each change goes quickly.

Know What Your Insert Does

An insert is the absorbent layer that sits inside a diaper cover or a pocket diaper. Inserts are usually made from cotton, bamboo, hemp, or microfiber, and they hold urine until the diaper is changed. Because inserts do the absorbing, the cover mainly keeps moisture from reaching clothes and bedding. Keep that in mind when you troubleshoot: a leak often means the insert is too small, too thin, or sitting in the wrong place, not that the cover failed.

Shopping for one? See our guide: Cloth Diapers or Disposable (2026): Which Is Better for Your Baby?.

Step-by-Step: Placing an Insert

  1. Lay the cover flat, outer side down, with the leg elastic relaxed.
  2. For a pocket diaper, open the back pocket and slide the insert in with the fabric side facing the baby’s skin.
  3. For a cover with a separate insert, lay the insert on top of the cover’s inner layer, centered from front to back.
  4. Position the thicker end toward the back for boys who wet heavily in the back, or toward the front for girls who wet in the front. Overnight, the thickest section should sit where your baby’s wetting is heaviest.
  5. Fasten the snaps or hook-and-loop closures at the size that keeps the waistband snug but not tight.

Layering Inserts for More Absorbency

If one insert is not enough, you can add a booster. Place the booster on top of the first insert, lined up with the area that gets the most wetness, and secure it with the cover so it doesn’t shift. Avoid stacking so many layers that the diaper becomes bulky, since bulk can cause gaps at the legs. Overnight use is where layering helps most. Many parents also add a booster for long naps or long car rides, where a single insert may not be enough.

Some inserts are designed to be folded into a trifold, which adds absorbency without much bulk. Check the manufacturer’s instructions for the fold shown on the package before you try a different style.

Fitting and Checking the Diaper

A good fit keeps the insert in place. Check the legs after you fasten the cover: the elastic should sit against the skin without red marks, and the insert should not bunch at the crotch. If you see gaps, the insert may be too short for the cover or the cover may be too large for your baby’s current size. Adjust the rise setting on your cover if it has one, and recheck after the first hour of wear.

Signs the Setup Needs Adjusting

  • Leaks at the legs usually mean the insert is not reaching the leg openings or the elastic is too loose.
  • Back leaks often point to a missing booster or an insert placed too far forward.
  • Wet clothes after a short time may mean the insert is too thin for the amount your baby wets.

Common Mistakes

  • Placing the insert with the wrong side facing the skin, which slows absorption.
  • Stacking too many layers, which creates bulk and gaps.
  • Skipping the fold on trifold inserts, leaving the thinnest part at the crotch.
  • Using a fabric softener on inserts, which reduces absorbency over time.
  • Changing the diaper too late and assuming the insert failed when the real issue was a full insert.
  • Bamboo cloth diaper inserts: Bamboo is a common choice for absorbent inserts, and many parents use it as a daytime layer. View on Amazon
  • Hemp cloth diaper boosters: Boosters add targeted absorbency for overnight use or heavy wetters. View on Amazon
  • Microfiber cloth diaper inserts: Microfiber absorbs quickly, so it works well as a first layer that wicks moisture away from the skin. View on Amazon

FAQ

Which side of the insert should face the baby?

For most pocket diapers, the soft or fleece side faces the baby, while the absorbent side faces the diaper’s inner layer. Check the labeling on your specific brand, since a few designs reverse this.

How many inserts should I use at night?

Many parents use one insert plus a booster overnight, but the right number depends on how much your baby wets and how long they sleep. Test your setup and adjust based on the results.

Can I use the same insert for every diaper change?

You should replace a soiled insert at every change. Clean inserts can be reused until they stop absorbing well, and your laundry routine affects how long they last. Consult the manufacturer’s care instructions for specifics.

Conclusion

Once you know how inserts work, placing them becomes a quick habit. Match the insert and any booster to your baby’s wetting pattern, check the fit after fastening, and adjust when leaks appear. Small changes in placement often solve the problem.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our natural & eco parenting guides, checking product details against manufacturer specifications and owner feedback.